A-guide-to-paint-your-own-home
Home builder's guide

A guide to painting
your own home

Tools, prep, technique and how much paint to buy.
This is where your design ideas come to life.

Open the paint calculator

Be your own painting contractor?

Painting can be fun but slow, especially the first time. A contractor costs money, so many families do it themselves. Weigh it up first.

15–20%Possible labour savings if you manage it yourself and everything goes right.

A general contractor saves money in other ways. They negotiate with subcontractors, manage the work to avoid extra costs, and already know who to hire.

Hiring a crew, handing over the design and getting a flawless job cheaply is not realistic. Doing it yourself works if you are organised, learn fast, and have money and design sense plus the time and drive to manage it.

Advantages

  • Save 15–20% on labour, if all goes to plan.
  • Full control, so you're more likely to get what you want.
  • Good subcontractors can deliver great quality, even if you lack experience.
  • The pride of doing it yourself.

Disadvantages

  • Surprise costs and overruns usually shrink the savings.
  • It takes longer and more effort than you expect.
  • Inexperience brings extra problems and can hurt the finish.
  • You carry the risk for costs and technical issues, during the job and after you move in.
  • Building finance can be harder to get.

Plan before you paint

There is always more to learn about painting. Good preparation makes the job faster and neater.

  • Think about the size and layout of your home.
  • Check you have every material and tool before you start.
  • Use specialised painting products. They improve both quality and speed.
  • Watch for sloppy work. Standard tools are made for general use and don't allow for your home's particular features.

Gather your tools

Good equipment makes the whole job run smoother. Hover or tap any item for more.

Choosing the paint

Emulsion (water-based)

Generally the more durable choice. Comes in matte, partly glossy and glossy finishes.

  • Recommended wherever it's practical.

Oil-based

Gives a silky, hard, high-gloss finish.

Where to begin

Prepare the surface before any paint goes on.

  1. 1Strip old wallpaper

    If you're remodelling, soak the paper with remover and wait the recommended time. Score it with a marking tool, then use a steamer to soften it if needed.

  2. 2Clean and scrub

    Clean floorboards and mouldings first so loose dirt doesn't spoil the walls. Remove oil and residue with TSP (trisodium phosphate) as the supplier directs, rinse with water and let dry. Sand in circles, wearing a face covering.

  3. 3Prime where needed

    Not every job needs primer, but experts advise it for the surfaces listed below.

  4. 4Check the old paint

    Latex paint won't go over oil-based paint. Rub the wall with a cotton swab dipped in alcohol. If paint comes off, it's latex. If not, it's oil-based.

  5. 5Smooth the surface

    Scrub any unpainted spots again to remove flaws that could show through. Then pick your paint type and colour.

Prime these surfaces

Unpainted drywallStained or repaired wallsBare woodGlossy finishesBig colour changes

Test older homes for lead. Homes built before 1978 may have lead paint. Test before you strip, and if it's positive, hire a professional to remove it.

Paint it the right way

Work from the top down for an even result.

  • Dip the brush about a quarter of the way in and wipe off the excess.
  • Cut in the edges first. Hold the brush like a pencil, use clean strokes and feather the edges to avoid drips.
  • A little paint on the trim is fine, since it gets painted last. Just don't get careless.
  • On walls, cut in one section, then roll it before moving on.

Work in pairs. It's easier with two: one person cuts in while the other rolls.

Have questions about which cement product to start with?

Reach out to the JSW Cement team before you start.

Contact JSW Cement

How much paint you'll need

One gallon covers about 400 sq ft. Multiply each wall's width by its height, add them up, then divide by 400.

Area to paint440 sq ft
Paint needed1.1 gallonsabout 4.2 litres

Based on the guide's 400 sq ft per gallon, for four walls with no deductions for doors or windows. Always check the coverage printed on your paint tin.

How long it takes

Plan your time realistically.

Days to weeksA full room can take anything from a few days to several weeks.

Keep the air moving. Good ventilation stops you breathing in too much of the paint's chemicals.

A home painted your way

It takes time, effort and preparation, but with the right tools and reliable paint you can do it yourself. A trusted contractor makes it calmer if you'd rather not. Next up: landscaping the outside of your home.