All-you-need-to-know-about-Drywalls
Home builder's guide

All you need to
know about drywall

Types, planning, tools, taping and joint compound.
An easy, effective alternative to traditional plaster.

See the tools

What drywall is

With plumbing and wiring done, the walls get closed in. Drywall is an easy, effective alternative to traditional plaster.

4 × 8 inchesThe standard panel size.

Lengths

8 to 16 inches

Widths

48 to 54 inches

Types of drywall

Beyond the standard panel, there is a type for most jobs.

Special-use panels

  • Moisture and mould resistant
  • Fire resistant
  • Abuse resistant
  • Aluminium
  • Foil-backed
  • ¼-inch flexible
  • ½-inch high-strength ceiling

Newer options

Lighter-weight panelsPanels that remove VOCs from the air

Why use drywall

It is quick to work with and does a lot for the finished wall.

Easy to work with

Panels are easy to find, cut and install.

Holds its shape

Flexible and resists sagging. Properly reinforced, it resists cracking too.

Takes decoration

Paint and other finishes go on well.

Less moisture

Reduces excess moisture during construction.

Fire protection

Gypsum doesn't burn, which adds a layer of fire safety.

Sound control

Helps keep noise between rooms down.

Plan the job

Insist on good material and neat, precise fitting. Then measure the framed walls to work out what you need.

Up to 25% fewer seamswhen you hang panels horizontally instead of vertically.

The seam also lands at a comfortable height for taping, except with 54-inch panels.

Use the full range of panel sizes to cut waste and seams.

Before you hang

  • All other inspections are complete.
  • Plumbing and electrical rough-ins are finished.
  • Insulation is in.

Long panels need two people. They tape and finish better, but they are heavy. Plan for a second pair of hands to lift and hang them.

Tools you'll need

Hover or tap any tool for more detail.

Measure and mark

Cut

Lift and reach

Fasten

Screws

  • What professionals use, with a screw gun.
  • Hold panel and frame together more tightly.
  • Cause less damage to the panel.
  • Match the thread type to the framing.

Nails

  • Driven with a hatchet-style drywall hammer.
  • Choose ring-shank nails over plain ones.
  • Drive them so ¾ of their length is in the framing.

Extra hold. Add drywall adhesive for more holding power.

Have questions about which cement product to start with?

Reach out to the JSW Cement team before you start.

Contact JSW Cement

New methods and materials

Newer products make for flatter seams and a stronger hold.

Vapour barrier

In colder climates, ceilings need a poly vapour or air barrier. Resilient channel gives a framing layout that stops the plastic being punctured.

Drywall backers

They pull butt edges inward into a recess that looks like a tapered seam. Fasteners can sit further from the edge, so fewer screws pop.

OSB backer

Turns a butt joint into a tapered one. It is easy to finish, flat and almost invisible in bright light. Keep it away from the plates so the sheet can bend to match.

Spray-foam adhesive

Polyurethane spray foam beats caulk-gun adhesive. It lays an even bead and holds harder, even on steel.

Cordless routers

They have replaced drywall saws for most cutting because they are faster.

Taping the drywall

Taping used to mean a trowel, taping knives, paper tape and a pail of joint compound. Newer hand and automatic tools have largely taken over.

Hand taping tools

Taping knives

For seams, corners and covering fasteners. Narrow 1:6-inch knives suit tight spots. Wider knives have a metal tip for resetting nail heads. Look for a stiff blade with a slight curve when viewed head-on.

Hawks and pans

A hawk holds compound while you work with the knife. A pan suits thinner compound and doubles as a mixing tub.

Curved trowels

Curved or bevelled trowels give better control over how much compound comes off than flat ones.

Wide straight-handled knives

Have a metal strip on the back for strength. Used to bed tape on seams when working with automatic tools.

Automatic toolsA machine for every taping step. Less labour, more done.

They are expensive, but you can rent them instead of buying.

Joint compound

Two main types, each suited to a different kind of job.

Drying type

One of the most popular. Mostly vinyl-based, and needs proper drying time between coats.

  • Pre-mixed: factory-set consistency, ready from the bucket, and can be resealed for later.
  • Powder: mix with water, then store and use like pre-mixed.

Setting type

Powder only. It hardens before it fully dries.

  • Harder to sand.
  • Needs real skill and experience for DIY. Otherwise hire a skilled contractor.

Walls closed in and ready to finish

Next up: the components of your roof.