plumbing-and-electric-installation
Home builder's guide

Plumbing and electrical
installation

Codes, pipes, sewer line, wiring, insulation and inspections.
The basics of a well-planned install.

Jump to wiring

Where this stage fits

It can look complicated. Here are the basics of a complete, well-planned installation.

After framing

Rough framing has laid out doors, walls, stairs and the like.

Side by side

Siding and roofing can go on while plumbing and wiring go in.

Done right

Follow the codes, plan each run and pass every inspection.

Plumbing codes

Codes are rules set by a country, state or city. They aim to make water use more efficient, and your plumber must follow them.

Codes matter most for

DrainagePipes and fittingsFixtures

Not sure what the codes say? Hire a plumber who knows them and can apply them.

Rough plumbing and electrical

This is when pipes and wires first go into the frame.

Pipes and wires

Plumbing and electrical contractors start running lines through inner walls, roofs and floors.

Drains and vents

Drain pipes and vents are fixed, with a water supply line to each connection.

Tubs and showers

Bathtubs and shower stalls go in now.

HVAC pipework

First piping for the heating, ventilation and air conditioning system and the furnace. HVAC vent pipes run up through the roof.

Insulation

Goes into the floors, ceilings and walls.

Bathroom design

A few choices make a bathroom comfortable and long-lasting.

  • Give it good ventilation and natural light.
  • Use high-quality bath and sanitary fittings to cut wear and tear.
  • Raise the bathroom floor 5 cm above the other floors in the house.

Countertop materials · hover or tap for more

Lay the sewer line

A badly laid line from the city may still work, but don't risk it. Follow these five steps.

  1. 1Work out the elevations

    Find how high the pipe must sit so it doesn't run deeper than needed. It starts at the home's main drain and slopes down to the city connection, called the tap. Use a laser level, GPS or standard survey tools to see where the ground needs levelling.

  2. 2Measure the slope

    Use the pipe's length and the two elevations. Slope is the vertical drop divided by the total length.

  3. 3Dig the trench and bed it

    Keep the trench as narrow as you can, and know where the pipe ends. The bottom should follow the slope and be smooth and firm. Lay sand as bedding: it supports the pipe and is easier to fine-tune than soil.

  4. 4Lay the pipe

    Fit one section at a time, starting from the low end.

  5. 5Backfill

    Cover the pipe with sand first to protect it and fill gaps. Then pack the soil back in layers.

4-inch PVCThe usual home sewer pipe, joined with solvent glue.

Local code decides the material and size you must use.

Electrical wiring

Wiring is critical work. Mistakes made without the right knowledge can be dangerous.

When

As the roof nears completion, the electrician fits light and switch boxes. Wiring starts after HVAC pipes and ducts are in, since wires are easier to route around them.

What

Wires run from the circuit breaker board to every box, including cable TV, music system and phone lines.

Plan the job

Draw a diagram

Show where the breaker box sits and the path to each outlet.

Lay the cable

Start with the longest run to waste less. Work from upstairs down to the basement. Leave about a foot of spare wire at each end.

Drill safely

Check behind the wall for cables and pipes first. Drill through the centre of each stud with a 1-inch bit.

Place the breaker box

Put it in the basement or a utility room so it is easy to reach later.

6 outletsper 110-volt circuit is the common guide for a living area.

That may not be enough for a bigger home. The article's example says a 1,500 sq ft house needs at least two circuits.

Wiring, step by step

  1. 1Pull the wire

    Set the roll near the breaker box and pull wire along the route in your diagram.

  2. 2Connect each circuit

    Take it to the nearest outlet or switch, or run it straight through the box.

  3. 3Strip the ends

    Use wire strippers.

  4. 4Attach

    Connect the wires to each outlet, fixture or switch.

One circuit per set. Give each set of wiring its own circuit, matched to the current it carries and what the outlet is for.

Have questions about which cement product to start with?

Reach out to the JSW Cement team before you start.

Contact JSW Cement

Insulation

Insulation stops heat moving in or out of the house. R-value measures how well it resists heat: the higher, the better.

Fibreglass

Pre-cut batts or rolls. Cheap and easy to fit between framing in walls, attics and open spaces.

  • Easy to work with
  • A fire risk if fitted wrongly
  • Vulnerable to moisture

Cellulose

Made from recycled newspaper and growing in popularity. Fills cavities, and also comes as boards and mats.

  • Eco-friendly
  • Resists fire and insects
  • Costly
  • Needs special equipment
  • Hard to fit around pipes
  • Needs drywall over it

Rigid foam

Helps control indoor temperature. Seals gaps and stops air leaks, often in thin walls and garage doors.

  • High R-value
  • Affordable
  • Cuts noise
  • Pests can get in if fitted wrongly

Waterproofing

Damp can do serious damage, and untreated water becomes a big problem fast.

Foundation

Waterproofing can be done inside or outside. Outside methods are best during construction.

Terraces

Rain and leaking water tanks can ruin flooring and seep through the slab below. Finish the structure and fit rainwater pipes and electrical conduits before you waterproof.

Kitchens and washrooms

Water pipes run under the floor, so waterproofing is a must to stop seepage into floors and walls.

Materials used

External waterproofing mixesKota stoneBitumen

Inspection

Local authorities do the final checks to confirm the building codes are met.

  1. 1Foundation inspection

    After curing, the inspector checks the foundation parts meet code and are fitted correctly.

  2. 2Systems inspection

    Covers rough framing, plumbing, and electrical and mechanical systems. It is often split into three separate checks, with framing done apart from electrical and mechanical.

  3. 3Drywall arrives

    Once inspection passes, drywall (also called plasterboard, wallboard or gypsum board) is delivered to site.

Pipes in, wires run, inspections passed

Next up: the tools and tape for drywall, the step that replaces traditional plaster. Explore JSW Cement